Current Version Updates.

If your logger has been sent for updating, future updates can be performed without sending you logger in.

To Update your logger:

Unplug and reconnect the logger, you must start the update process before five minutes of plugging the logger. As a safety precaution the logger will not accept incoming connections after five minutes.

Press the reset button to obtain the loggers current IP address (see manual).

On a separate computer using a browser Login to the loggers update page at http://[IP Address]/update (i.e. http://10.0.0.125/update).

Click "Get Info From Server"

Then

Click "Update Firmware"

The Screen will display the progress.

Once the logger reboots the update is complete.

If you cannot connect to the page:

Reset the logger and make sure the IP address is not all 0's

If it does connect to you network and you cannot reach this page

Your logger must be sent in.

Once updated you will give you the ability to perform future updates as above.

Get your Unit Updated

If you have been affected by the Dropbox update, you will need to send your unit in to be updated.

This update cannot be done at your location it must be sent in.

Please send in your logger only. We do not need the SD card, cable or any other accessory. This is for both the Midmark and Tuttnauer units.

We are offering this update free of charge for all units whether or not you unit is under warranty.

To update your unit you will need to send it in to:

Alt Dataloggers

Attn: Update

32A Camp Street

West Yarmouth, MA 02673

Please include the return address IN the box.

Do not rely on the return address on the outside of the box.

We will update your unit and have it shipped out within 24 hours from time of receipt.

We apologize for this inconvenience.

You will receive the latest released update.

This should be the one and only time you need to send your unit in.

Again we apologize for this inconvenience and appreciate you understanding.

See below for setup instructions for your updated logger.

Version Info

Bold updates are recommended; the others are optional.

Your unit must be sent in to get v 5.0. After that you will have the ability to perform the updates at your location.

M19 - Midmark 1st Gen

v 5.0 - Adds the ability to remotely update your logger from your location. No more sending your unit in for updates.
v 5.1 - Displays the model and current firmware version on startup.
v 5.2 - Adds the ability to select if the load numbers are displayed. This affects both the printout and on-screen display. The load count will still be counted and stored. If it is re-enabled, it will display current value not the value where it was disabled. Once this update is installed you will need to enable load numbers via the setup page. SEE FAQ Page.

M22 - Midmark 2nd Gen

v 5.0 - Adds the ability to remotely update your logger from your location. No more sending your unit in for updates.
v 5.1 - Displays the model and current firmware version on startup.
v 5.2 - Adds the ability to select if the load numbers are displayed. This affects both the printout and on-screen display. The load count will still be counted and stored. If it is re-enabled, it will display current value not the value where it was disabled. Once this update is installed you will need to enable load numbers via the setup page. SEE FAQ Page.

M42 - Midmark 3rd Gen

v 5.0 - Adds the ability to remotely update your logger from your location. No more sending your unit in for updates.
v 5.1 - Displays the model and current firmware version on startup.
v 5.2 - Adds the ability to select if the load numbers are displayed. This affects both the printout and on-screen display. The load count will still be counted and stored. If it is re-enabled, it will display current value not the value where it was disabled. Once this update is installed you will need to enable load numbers via the setup page. SEE FAQ Page.

T01 - Tuttnauer

v 5.0 - Adds the ability to remotely update your logger from your location. No more sending your unit in for updates.
v 5.1 - Displays the model and current firmware version on startup.
v 5.2 - Adds the ability to select if the load numbers are displayed. This affects both the printout and on-screen display. The load count will still be counted and stored. If it is re-enabled, it will display current value not the value where it was disabled. Once this update is installed you will need to enable load numbers via the setup page. SEE FAQ Page.